See every stage from the box before you hang a plate.
A free browser tool for steel match directors: RCSA Rimfire Challenge, outlaw steel and speed steel. Enter your club’s steel once, and From The Box builds fresh pistol and rifle stages, shows the shooter’s sight picture with the angle to every target, and prints stage sheets your crew can set from.
From the steel shed to stage sheets in four steps
Set up your club once
Lane width and distances, your post types and their real heights, and every plate you own: circles, squares, rects, diamonds and stops, plus custom plates like poppers and silhouettes. Mark which posts can carry a stop plate or a rectangle. This is the step that matters — every stage is built from it.
Generate the match
Pick pistol, rifle or both, and a 1–5 star difficulty for each stage. You get five to seven plates per stage with one stop plate, laid out inside your lane using only steel you have.
Check the view from the box
Every target shows its horizontal and vertical angle from the shooter. Plates that sit too close together, or hide behind a nearer post, get flagged before anyone drives a stake. Drag any plate on the map, or swap posts, plates and yardage right in the stage table, then check the view from the box.
Print and set
One 8.5×11 sheet per stage with the diagram, distances, plate and post legend and round count, plus a 2×2 overview of the whole match for the setup crew and a steel pull list of every post and plate to load.
Set up your club right, and everything after it is right
From The Box only builds with the steel you tell it you have. Your lane width and distances decide where plates can go. Your real post heights decide what the shooter can see from the box. Your plate and stop plate counts decide what gets hung, and the pull list checks against them. Count what is actually in your shed, measure your posts, and mark which ones take a stop plate or a rectangle. Ten minutes here saves you resetting steel on match day.
Hand your crew a sheet, not a sketch
Distances to the yard, spacing between plates in feet and inches, which post each plate goes on, and which one is the stop. Setup goes faster and matches look the same as the plan.
- Diagram with centerline, distances and plate spacing
- Sight angles for every target
- Plate and post legend with your post heights
- Targets, strings and round count
Built by an MD, for MDs
From The Box started as the tool I wanted for our own matches at Douglas Ridge. It’s free to use. If it saves your crew a Saturday morning, a donation helps keep it going.
Get word when new features land
More stand types and match-day tools are on the way. One email when something ships, nothing else.
Why does club setup matter so much?
The whole app runs on it. Stages, hidden-plate warnings, the view from the box, the steel pull list and the inventory limits all come from what you enter in Club Setup. Wrong post heights mean wrong sight lines; wrong counts mean a stage you can’t hang. Enter what you really own and the Generate tab shows a steel check so you can spot gaps before match day.
Can I use it for outlaw steel or speed steel?
Yes. Each stage is a fresh layout of 5 to 7 plates with a stop plate shot last, built only from the steel you own, which is how most outlaw and speed steel matches run. Set your minimum distance in Club Setup to what your range and plate maker allow. That’s often 10 yards for pistol calibers, and some clubs are cleared for 7. The app never puts steel closer than 7 yards.
Does it work for Steel Challenge?
Not for sanctioned Steel Challenge (SCSA). Those eight stages are fixed and published by USPSA, so there is nothing to generate. For club matches that want new layouts every time, like outlaw steel and speed steel, From The Box is built for exactly that.
Can I change a generated stage?
Yes. Drag any plate, stop plate included, anywhere inside your lane, or tap it and fine-tune in 6-inch and 1-yard steps. You can also swap a post, plate or yardage from the stage table, check it in the view from the box, undo a move, or give one stage a new layout without touching the rest. The app warns you if a plate gets hidden, and never lets you use more steel than you own.
What do I need to run it?
A laptop or tablet with a current browser, and a printer for the stage sheets.
